Instruction manual for Twin Crane MHI Nagasaki / TDC control equipment (synchro-unit)
Year: 1983 Language: english Author: NIPPON ELECTRIC INDUSTRY Genre: Instruction manua Publisher: NIPPON ELECTRIC INDUSTRY Format: PDF Quality: Scanned pages Number of pages: 35+72 Description: INSTRUCTION MANUAL FOR TDC CONTROL EQUIPMENT (SYNCHRO-UNIT) JULY 4, 19S3 NIPPON ELECTRIC INDUSTRY CO.,LTD.-CONTENTS 1 . GENERAL.....................................1 5. PRINCIPLE OF OPERATION........................................2 6. IDENTIFICATION OF EACH PART...................................4 7. INSTALLATION AND ADJUSTMENT...................................7 8 . OPERATING PROCEDURES.........................................12 9. TROUBLE SHOOTING ...........................................14 10. SYNCHRO-TRANSMITTER INSPECTION...............................18 11. DC SOURCE INSPECTION.........................................19 12. RELAY REPLACING METHOD......................................2 0 13. CARD REPLACING METHOD........................................21 14. TEST FUNCTIONS................................................. 2 3-1 . GENERAL This equipment is used for controlling KDIST and LUFFING functions of the Twin-Deck CraneAMAIN and SUB crane. For HOIST and LUFF functions, the equipment carries out a synchronous control. 5. PRINCIPLE OF OPERATION 5.1 Method of Synchronous Control When a control of identical speed is given to Main Crane (hereinafter called main) and to Sub-Crane (hereinafter called sub) from the control lever, if the speed characteristics of the main are different from those of sub, a deviation is produced in the position of two cranes When the deviation is smaller than certain value (Speed compensation dead zone), a signal from the control lever will be outout as it is. When the deviation is larger than certain value, a compensation will be added to the speed control instructi ri in cr : :c aiike the deviation smaller. In case of Fig. 1, the main lags behind the sub in the direction of travelling, so the value corresponding :o (speed :r.strJ: tion) + (compensation) will be given to main as instruction val:e. On the contrary, since the sub advances more t lan the main, it will receive (speed instruction) - (compensation) instruction. In twin-operation node, the synchro-trar.. .ir.itter JeiActi a deviation between the main crane and sub-crane. The deviation is converted into speed compensation signal in synchro unit, then added to or subtracted from the speed instruction signal given by the control lever, and is output as a speed signal. Also, when the deviation between the mair and sub becomes larger than a set value (stop point), stop signal will be issued as the synchronism is no more available.
Вы не можете начинать темы Вы не можете отвечать на сообщения Вы не можете редактировать свои сообщения Вы не можете удалять свои сообщения Вы не можете голосовать в опросах Вы не можете прикреплять файлы к сообщениям Вы не можете скачивать файлы
Instruction manual for Twin Crane MHI Nagasaki / TDC control equipment (synchro-unit)
Year: 1983
Language: english
Author: NIPPON ELECTRIC INDUSTRY
Genre: Instruction manua
Publisher: NIPPON ELECTRIC INDUSTRY
Format: PDF
Quality: Scanned pages
Number of pages: 35+72
Description: INSTRUCTION MANUAL FOR TDC CONTROL EQUIPMENT (SYNCHRO-UNIT) JULY 4, 19S3 NIPPON ELECTRIC INDUSTRY CO.,LTD.-CONTENTS
1 . GENERAL.....................................1
5. PRINCIPLE OF OPERATION........................................2
6. IDENTIFICATION OF EACH PART...................................4
7. INSTALLATION AND ADJUSTMENT...................................7
8 . OPERATING PROCEDURES.........................................12
9. TROUBLE SHOOTING ...........................................14
10. SYNCHRO-TRANSMITTER INSPECTION...............................18
11. DC SOURCE INSPECTION.........................................19
12. RELAY REPLACING METHOD......................................2 0
13. CARD REPLACING METHOD........................................21
14. TEST FUNCTIONS................................................. 2 3-1 . GENERAL
This equipment is used for controlling KDIST and LUFFING functions of the Twin-Deck CraneAMAIN and SUB crane.
For HOIST and LUFF functions, the equipment carries out a synchronous control.
5. PRINCIPLE OF OPERATION
5.1 Method of Synchronous Control
When a control of identical speed is given to Main Crane (hereinafter called main) and to Sub-Crane (hereinafter called sub) from the control lever, if the speed characteristics of the main are different from those of sub, a deviation is produced in the position of two cranes When the deviation is smaller than certain value (Speed compensation dead zone), a signal from the control lever will be outout as it is.
When the deviation is larger than certain value, a compensation will be added to the speed control instructi ri in cr : :c aiike the deviation smaller.
In case of Fig. 1, the main lags behind the sub in the direction of travelling, so the value corresponding :o (speed :r.strJ: tion) + (compensation) will be given to main as instruction val:e. On the contrary, since the sub advances more t lan the main, it will receive (speed instruction) - (compensation) instruction.
In twin-operation node, the synchro-trar.. .ir.itter JeiActi a deviation between the main crane and sub-crane.
The deviation is converted into speed compensation signal in synchro unit, then added to or subtracted from the speed instruction signal given by the control lever, and is output as a speed signal.
Also, when the deviation between the mair and sub becomes larger than a set value (stop point), stop signal will be issued as the synchronism is no more available.
Twin Crane MHI Nagasaki
Скачать [12 KB]
Поделиться